Hyprscroll2D

Hyprscroll2D is an experimental two-dimensional scrolling layout for Hyprland. It turns a workspace into an expandable grid and lets you move through it in every direction.

Unlike column-only scrolling layouts, windows can live above, below, left and right of each other. Configurable edge peeks keep nearby rows and columns visible, so you never lose the shape of your workspace.

What works

• Infinite two-dimensional window placement
• Focus and camera movement on both axes
• Directional window movement with collision swapping
• Independent width and height presets
• Visible edge peeks for neighboring rows and columns
• Per-workspace in-memory layout state
• Omarchy bindings that fall back to the normal action outside Hyprscroll2D

Status

v0.2.0 is an experimental preview for Hyprland 0.56.x. It has been live-tested on Hyprland 0.56.2 and is intentionally enabled on only one workspace during evaluation.

The layout uses Hyprland's Lua custom-layout API, so it does not require a compiled Hyprland plugin. Native Omarchy Shell packaging loads the layout and keeps it active across Hyprland config reloads. Other Lua-configured Hyprland installations can load the layout, but must provide their own bindings.

Install on Omarchy

Recommended: Omarchy plugin command

Requirements:

• Current Omarchy Quattro with Hyprland 0.56.x

Install and enable directly from GitHub:

omarchy plugin add https://github.com/kirollosatef/hyprscroll2d --enable

The plugin loads Hyprscroll2D at runtime without editing your Hyprland config. It enables the layout only on workspace 9. Press Super+9, open a few windows, and try the controls below.

Update it later with:

omarchy plugin update io.github.kirollosatef.hyprscroll2d

The repository contains a validated Omarchy manifest.json and can be installed through the official omarchy plugin command today. A listing on the community Omarchy Plugin Marketplace is a separate review process and does not make a plugin part of Omarchy's bundled first-party plugins.

Alternative: config installer

If your Omarchy version does not yet provide omarchy plugin, clone the project and run the config installer:

Clone the project and run the installer:

git clone https://github.com/kirollosatef/hyprscroll2d.git \
  ~/.local/share/hyprscroll2d
~/.local/share/hyprscroll2d/install.sh

This alternative installer:

• creates a timestamped backup of ~/.config/hypr/hyprland.lua;
• enables Hyprscroll2D only on workspace 9;
• reloads Hyprland and checks for configuration errors;
• restores the backup automatically if the new block causes an error.

To use a different experimental workspace, pass its number:

~/.local/share/hyprscroll2d/install.sh 8

For a manual installation, add the following near the end of ~/.config/hypr/hyprland.lua, after the Omarchy defaults and your normal require("hypr.*") lines:

local hyprscroll2d = os.getenv("HOME") .. "/.local/share/hyprscroll2d"
dofile(hyprscroll2d .. "/layout/init.lua")
dofile(hyprscroll2d .. "/integration/omarchy.lua")

-- Start safely on one experimental workspace.
hl.workspace_rule({ workspace = "9", layout = "lua:hyprscroll2d" })

Then reload and validate the configuration:

hyprctl reload
hyprctl configerrors

If hyprctl configerrors prints nothing, the manual setup is ready.

Controls

Action	Binding
Focus a window	Super+Arrow
Move or swap a window	Super+Shift+Arrow
Pan the camera	Super+Ctrl+Arrow
Grow window width	Super+-
Shrink window width	Super+=
Grow window height	Super+Shift+=
Shrink window height	Super+Shift+-

These keys retain Omarchy's normal behavior whenever the active window is not using Hyprscroll2D.

Customize the layout

Edit layout/config.lua to change:

• peek_x and peek_y: visible pixels from neighboring columns and rows
• gap_x and gap_y: spacing between cells
• width_steps and height_steps: available size presets
• default_width_step and default_height_step: initial window dimensions

Reload Hyprland after changing the values.

Update a config installation

git -C ~/.local/share/hyprscroll2d pull --ff-only
hyprctl reload
hyprctl configerrors

Uninstall

If installed using omarchy plugin add, run:

omarchy plugin remove io.github.kirollosatef.hyprscroll2d --yes
hyprctl reload

The reload restores Omarchy's normal bindings and removes the runtime layout.

If installed using the alternative config installer, run its uninstaller before deleting the repository:

~/.local/share/hyprscroll2d/uninstall.sh

It removes only the marked Hyprscroll2D block and creates another timestamped config backup. Once it finishes, remove the cloned repository:

rm -rf ~/.local/share/hyprscroll2d

Known limitations

• State is reset when Hyprland reloads.
• Fullscreen, groups, multi-monitor moves, and special workspaces need more testing.
• The bundled conditional keybinding integration supports Omarchy.
• Compatibility outside Hyprland 0.56.x is not yet guaranteed.

Please report issues with your Hyprland version, monitor geometry, relevant configuration, and exact reproduction steps.

Development

Run the full test and syntax suite:

make check

The geometry and navigation engine is isolated from Hyprland APIs so it can be tested with plain Lua. See docs/DESIGN.md for the behavioral model and roadmap, and docs/RESEARCH.md for related projects, important differences and technical background.

Contributing

Contributions and real-world testing are welcome. Read CONTRIBUTING.md before opening a pull request.

Created by kirollosatef.

License

MIT