feat: add ESP32-C5 Touch LCD 1.9 board profile

README.md

@@ -104,6 +104,7 @@ such as `spi_sd` describe a bus; they do not imply a complete storage applicatio
 <!-- BEGIN SUPPORTED_BOARDS -->
 | Board | Chip | Device definitions | Peripheral definitions |
 | --- | --- | --- | --- |
+| [`esp32_c5_touch_lcd_1_9`](boards/esp32_c5_touch_lcd_1_9/) | ESP32-C5 | `lcd_st7789v2`, `touch_cst816d`, `imu_qmi8658`, `tf_card`, `bat_axp2602` | `i2c_master`, `spi_tf`, `gpio_boot`, `gpio_power_key`, `ledc_backlight`, `gpio_touch_reset`, `gpio_touch_int`, `gpio_imu_int`, `gpio_axp_int` |
 | [`esp32_s3_lr1121_epaper_2_9`](boards/esp32_s3_lr1121_epaper_2_9/) | ESP32-S3 | `status_led`, `epaper_power_ctrl`, `epaper_ssd16xx`, `rtc_pcf85063a`, `bat_axp2602`, `radio_lr1121` | `i2c_master`, `spi_shared`, `gpio_boot`, `gpio_epaper_power` |
 | [`esp32_s3_lr1121_oled_1_54_xf`](boards/esp32_s3_lr1121_oled_1_54_xf/) | ESP32-S3 | `button_boot`, `button_power`, `button_menu`, `button_ptt`, `button_rtc_irq`, `radio`, `oled`, `rtc`, `battery`, `audio`, `sdcard` | `i2c_main`, `spi_radio`, `gpio_boot`, `gpio_power`, `gpio_menu`, `gpio_ptt`, `gpio_rtc_irq`, `gpio_amplifier`, `gpio_radio_cs`, `gpio_radio_irq`, `gpio_radio_reset`, `gpio_radio_busy`, `i2s_speaker`, `i2s_microphone` |
 | [`esp32_s3_touch_amoled_1_75c`](boards/esp32_s3_touch_amoled_1_75c/) | ESP32-S3 | `axp2101_power_manager`, `audio_dac`, `audio_adc`, `display_lcd`, `lcd_touch` | `i2c_master`, `i2s_audio_out`, `i2s_audio_in`, `gpio_pa_control`, `spi_display` |

README_ZH.md

@@ -102,6 +102,7 @@
 <!-- BEGIN SUPPORTED_BOARDS -->
 | 开发板 | 芯片 | 设备定义 | 外设定义 |
 | --- | --- | --- | --- |
+| [`esp32_c5_touch_lcd_1_9`](boards/esp32_c5_touch_lcd_1_9/) | ESP32-C5 | `lcd_st7789v2`, `touch_cst816d`, `imu_qmi8658`, `tf_card`, `bat_axp2602` | `i2c_master`, `spi_tf`, `gpio_boot`, `gpio_power_key`, `ledc_backlight`, `gpio_touch_reset`, `gpio_touch_int`, `gpio_imu_int`, `gpio_axp_int` |
 | [`esp32_s3_lr1121_epaper_2_9`](boards/esp32_s3_lr1121_epaper_2_9/) | ESP32-S3 | `status_led`, `epaper_power_ctrl`, `epaper_ssd16xx`, `rtc_pcf85063a`, `bat_axp2602`, `radio_lr1121` | `i2c_master`, `spi_shared`, `gpio_boot`, `gpio_epaper_power` |
 | [`esp32_s3_lr1121_oled_1_54_xf`](boards/esp32_s3_lr1121_oled_1_54_xf/) | ESP32-S3 | `button_boot`, `button_power`, `button_menu`, `button_ptt`, `button_rtc_irq`, `radio`, `oled`, `rtc`, `battery`, `audio`, `sdcard` | `i2c_main`, `spi_radio`, `gpio_boot`, `gpio_power`, `gpio_menu`, `gpio_ptt`, `gpio_rtc_irq`, `gpio_amplifier`, `gpio_radio_cs`, `gpio_radio_irq`, `gpio_radio_reset`, `gpio_radio_busy`, `i2s_speaker`, `i2s_microphone` |
 | [`esp32_s3_touch_amoled_1_75c`](boards/esp32_s3_touch_amoled_1_75c/) | ESP32-S3 | `axp2101_power_manager`, `audio_dac`, `audio_adc`, `display_lcd`, `lcd_touch` | `i2c_master`, `i2s_audio_out`, `i2s_audio_in`, `gpio_pa_control`, `spi_display` |

boards/esp32_c5_touch_lcd_1_9/README.md

@@ -0,0 +1,28 @@
+# ESP32-C5-Touch-LCD-1.9
+
+[简体中文](README_ZH.md)
+
+Waveshare ESP32-C5-WROOM-1-N16R8 board with a 1.9-inch SPI LCD.
+This profile is imported from the product examples and preserves their named
+peripherals and custom device metadata. Applications implement product policy;
+custom devices use `init_skip: true` so generic Board Manager initialization does
+not implicitly initialize the display, sensors, storage or battery gauge.
+
+- I2C: port 0, SDA GPIO2, SCL GPIO3, internal pull-ups enabled.
+- SPI2 shared by LCD and TF: MOSI5, MISO6, SCLK7; TF CS4.
+- LCD: ST7789-compatible, 170 x 320, X gap35; CS23/DC24/RESET26, backlight10.
+- Touch: CST816D-compatible 0x15, RESET8/INT0.
+- IMU: QMI8658 0x6B, INT1; gauge: AXP2602 0x62, INT25, 10 milliohm shunt.
+- BOOT28 and power-key9 are inputs. The power latch is not a software output.
+
+Reference: [product documentation](https://www.waveshare.com/wiki/ESP32-C5-Touch-LCD-1.9).
+Pin assignments were compared with the supplied product schematic. LCD controller,
+visible geometry, gap and touch compatibility retain the product implementation;
+the board owner has confirmed display, touch, sensor, storage and sleep/wakeup
+functionality using the product firmware on the correct ESP32-C5 rev v1.0 board.
+These observations do not establish a manufacturer-approved panel specification. Flash/PSRAM and application features are
+configured by the consuming application, not inferred from profile generation.
+
+Validation and migration: this change adds a profile and does not certify physical
+operation of arbitrary consuming applications. The product repository must retain its local definition until this PR
+is merged, the component registry publishes it and consuming application tests pass.

boards/esp32_c5_touch_lcd_1_9/README_ZH.md

@@ -0,0 +1,22 @@
+# ESP32-C5-Touch-LCD-1.9
+
+[English](README.md)
+
+微雪 ESP32-C5-WROOM-1-N16R8、1.9 英寸 SPI LCD 开发板。
+本配置保留产品示例的外设名称和自定义设备元数据；自定义设备使用
+`init_skip: true`，显示、传感器、存储和电量计的初始化策略由应用实现。
+
+- I2C：端口 0，SDA GPIO2、SCL GPIO3，启用内部上拉。
+- LCD 与 TF 共用 SPI2：MOSI5、MISO6、SCLK7；TF CS4。
+- LCD：ST7789 兼容，170 x 320，X 偏移35；CS23/DC24/RESET26，背光10。
+- 触摸：CST816D 兼容，地址0x15，RESET8/INT0。
+- IMU：QMI8658 0x6B、INT1；电量计：AXP2602 0x62、INT25、10毫欧采样电阻。
+- BOOT28 与电源按键9均为输入，不通过软件驱动电源锁存按键。
+
+参考：[产品文档](https://www.waveshare.com/wiki/ESP32-C5-Touch-LCD-1.9)。
+引脚与提供的产品原理图进行了核对。LCD 控制器、显示尺寸、偏移和触摸兼容性
+沿用产品实现。持有人已在正确的 ESP32-C5 rev v1.0 板卡上确认产品固件的显示、
+触摸、传感器、存储和睡眠唤醒基本功能；这些结果不等于屏厂参数认证。Flash、PSRAM 和应用功能由使用方配置。
+
+本变更新增板型，不代表任意使用方应用均已完成硬件验收。产品仓库应在本 PR 合入、组件注册表
+发布且使用方验证通过后，再删除自己的本地板定义。

boards/esp32_c5_touch_lcd_1_9/board_devices.yaml

@@ -0,0 +1,74 @@
+devices:
+  - name: lcd_st7789v2
+    chip: st7789v2
+    type: custom
+    version: 1.0.0
+    init_skip: true
+    config:
+      width: 170
+      height: 320
+      x_gap: 35
+      pclk_hz: 40000000
+      invert_color: true
+      sclk_gpio: 7
+      mosi_gpio: 5
+      cs_gpio: 23
+      dc_gpio: 24
+      reset_gpio: 26
+      backlight_gpio: 10
+      backlight_active_level: 1
+
+  - name: touch_cst816d
+    chip: cst816d
+    type: custom
+    version: 1.0.0
+    init_skip: true
+    config:
+      address: 0x15
+      frequency: 400000
+      reset_gpio: 8
+      interrupt_gpio: 0
+      width: 170
+      height: 320
+    peripherals:
+      - name: i2c_master
+
+  - name: imu_qmi8658
+    chip: qmi8658
+    type: custom
+    version: 1.0.0
+    init_skip: true
+    config:
+      address: 0x6B
+      interrupt_gpio: 1
+    peripherals:
+      - name: i2c_master
+
+  - name: tf_card
+    chip: micro_sd
+    type: custom
+    version: 1.0.0
+    init_skip: true
+    config:
+      mode: sdspi
+      cs_gpio: 4
+      mosi_gpio: 5
+      miso_gpio: 6
+      sclk_gpio: 7
+    peripherals:
+      - name: spi_tf
+
+  - name: bat_axp2602
+    chip: axp2602
+    type: custom
+    version: 1.0.0
+    init_skip: true
+    config:
+      address: 0x62
+      frequency: 400000
+      sense_resistor_mohm: 10
+      idle_current_threshold_ma: 1
+      interrupt_gpio: 25
+      irq_connected: true
+    peripherals:
+      - name: i2c_master

boards/esp32_c5_touch_lcd_1_9/board_info.yaml

@@ -0,0 +1,5 @@
+board: esp32_c5_touch_lcd_1_9
+chip: esp32c5
+version: 1.0.0
+description: "Waveshare ESP32-C5-Touch-LCD-1.9 (N16R8)"
+manufacturer: "Waveshare"

boards/esp32_c5_touch_lcd_1_9/board_peripherals.yaml

@@ -0,0 +1,94 @@
+peripherals:
+  - name: i2c_master
+    type: i2c
+    role: master
+    config:
+      port: 0
+      pins:
+        sda: 2
+        scl: 3
+      enable_internal_pullup: true
+      glitch_count: 7
+
+  # LCD and TF share GPIO5 as MOSI and GPIO7 as SCLK. TF reads data on GPIO6.
+  - name: spi_tf
+    type: spi
+    role: master
+    config:
+      spi_bus_config:
+        spi_port: SPI2_HOST
+        mosi_io_num: 5
+        miso_io_num: 6
+        sclk_io_num: 7
+        quadwp_io_num: -1
+        quadhd_io_num: -1
+        max_transfer_sz: 13600
+
+  - name: gpio_boot
+    type: gpio
+    role: io
+    config:
+      pin: 28
+      mode: GPIO_MODE_INPUT
+      pull_up: true
+      pull_down: false
+      default_level: 1
+
+  - name: gpio_power_key
+    type: gpio
+    role: io
+    config:
+      pin: 9
+      mode: GPIO_MODE_INPUT
+      pull_up: true
+      pull_down: false
+
+  - name: ledc_backlight
+    type: ledc
+    role: none
+    config:
+      gpio_num: 10
+      channel: LEDC_CHANNEL_0
+      timer_sel: LEDC_TIMER_0
+      freq_hz: 1000
+      duty: 0
+      duty_resolution: LEDC_TIMER_8_BIT
+      speed_mode: LEDC_LOW_SPEED_MODE
+      output_invert: false
+      sleep_mode: LEDC_SLEEP_MODE_NO_ALIVE_NO_PD
+
+  - name: gpio_touch_reset
+    type: gpio
+    role: io
+    config:
+      pin: 8
+      mode: GPIO_MODE_OUTPUT
+      default_level: 1
+
+  - name: gpio_touch_int
+    type: gpio
+    role: io
+    config:
+      pin: 0
+      mode: GPIO_MODE_INPUT
+      pull_up: true
+      pull_down: false
+
+  - name: gpio_imu_int
+    type: gpio
+    role: io
+    config:
+      pin: 1
+      mode: GPIO_MODE_INPUT
+      pull_up: true
+      pull_down: false
+
+  - name: gpio_axp_int
+    type: gpio
+    role: io
+    config:
+      pin: 25
+      mode: GPIO_MODE_INPUT
+      pull_up: true
+      pull_down: false
+      intr_type: GPIO_INTR_NEGEDGE

docs/CI.md

@@ -15,8 +15,8 @@ published versions satisfying the range are tested, with duplicates removed.
 Registry lookup failures fail the job. Each matrix entry records an exact version.
 
 The initial Board Manager floor is **0.7.2**, matching the reference board-pack
-template. Six board profiles are discovered. Each resolved Board Manager version
-adds twelve builds across the two IDF lines. Keep the floor until a deliberate
+template. Seven board profiles are discovered. Each resolved Board Manager version
+adds fourteen builds across the two IDF lines. Keep the floor until a deliberate
 compatibility change is tested. Unsupported catalog profiles or generation failures fail CI; they are
 not counted as successful builds.
 

docs/CI_ZH.md

@@ -13,7 +13,7 @@
 相同版本合并。组件库查询失败会使任务失败，每个矩阵项均记录明确版本。
 
 Board Manager 初始最低版本为 **0.7.2**，与参考板卡包模板一致。
-当前发现六块板卡，每个解析出的 Board Manager 版本在两个 IDF 版本线上共十二项编译。
+当前发现七块板卡，每个解析出的 Board Manager 版本在两个 IDF 版本线上共十四项编译。
 调整最低版本前需要明确兼容性变更并测试。
 不支持的芯片能力配置或生成失败会使 CI 失败，不会被计为编译成功。